Choosing the Right Septum for Food Safety Analysis Applications

Sep 12, 2023 · Disc valves are almost exclusively found in food processing applications. Key specifications include valve type, actuator type, port connections, valve size, and the materials of construction. Disc valves are used in food, pharmaceutical, and dairy industries to for shut-off service of liquid, powder, or food slurries where sanitation is critical.

Choosing the right septa. When choosing proper septa, there are many factors to consider: type of solvent or sample, slit or non-slit design, and reseal ability. These factors ultimately lead to material makeup of the septa.

The Dean-Stark apparatus is designed to collect water produced in synthetic reactions carried out under reflux. The reactions are normally done in solvents (for example toluene) that remove water formed in a reaction as an azeotrope. The condensed mixture of toluene and water collects in the burette and the denser water separates and falls to

Food Safety and Quality Management (FSQMS) and Hazard Analysis Critical Control Point (HACCP) systems. The critical components of this decision making process are shown in Figure 1. Detection testing ensures that everything present in the food or drink is supposed to be there; measurement ensures that it is there in the right

to the standard red rubber. This septum has characteristics similar to the gray butyl stopper with a slightly smaller temperature range of –20 t0 100°C. The Black Rubber septum is an economical choice for applications where reduced levels of vapor penetration are desired. Black rubber septa should be used with sturdier injection needles.

Mar 17, 2021 · Research purposes from the analysis of meteorites 3 to natural products 4; Safety and monitoring from environmental samples, microplastics and food 5-8 and wine, to forensics. 9; Gas chromatographs are frequently hyphenated to mass spectrometers (GC-MS) to enable the identification of the chemical components.

An economical septum for lower temperature (125°C) or low-pressure applications. Gray Butyl stoppers do not provide a PTFE film barrier and are not suitable for use with alkanes, benzene, chlorinated solvents or cyclohexane. Butyl rubber stoppers are preferred for analysis of fixed gases and where absolute resistance to

Jun 22, 2017 · In the current study, the deformed length of the nasal septum was defined as the maximal side of flexure (Fig. 1, indicated by the letter a). The strained side of the deformed septum cartilage was potentially caused by the nasal bone (upper side, a1), vomer and nasal crest of maxilla (lower side, a2).

Nov 29, 2018 · PTFE chemical resistance until pierced then the septa will have the compatibility of rubber. Not recommended when retaining samples for further analysis or for multiple injections. Temperature range -40°C to 110°C. Moulded Polypropylene Septa. Only suitable for single injection use – not recommended for sample storage before or after injection.

Feb 20, 2021 · Section 2: Safety Precautions and Waste Disposal . Safety Precautions: Use of eye protection is recommended for all experimental procedures. Sulfuric acid (H 2 SO 4) is highly corrosive. Avoid contact with your eyes, skin, and clothing. In case of contact, rinse with plenty of water. Ask instructor to assist with the cleaning of any spills.

Apr 16, 2022 · The aim of this study was to evaluate the interradicular septum bone morphometric characteristics using cone beam computed tomography (CBCT) images, as well as to establish quantitative shortcuts to allow clinicians to make a faster and more reliable plan for immediate implant placement in the maxillary molars area. This retrospective quantitative study was conducted on CBCT images obtained

10 µL, cone-tip, 23/26s tapered needle, gas-tight (PTFE-Tipped Plunger) are ideal for most S/SL and MMI applications. 23/26s tapered needles offer the tensile strength of a larger needle while minimizing puncture size in the septum. Blue Line nano-volume syringes (1 µL volume) are half-marked. The ALS should be configured for 2x the syringe

Aug 29, 2023 · Gas chromatography is a term used to describe the group of analytical separation techniques used to analyze volatile substances in the gas phase. In gas chromatography, the components of a sample are dissolved in a solvent and vaporized in order to separate the analytes by distributing the sample between two phases: a stationary phase and a

Choose the right Spare Parts Kit A small investment in a METTLER TOLEDO spare parts kit can buy you peace of mind that your line is never stopped due to failure of your product inspection equipment. You can choose between four different spare parts packages: Spare Parts Kit "Basic": This kit provides you with reliable protection right from the

Chiralizer Services, LLC. Nathan has provided a detailed answer already, but my suggestion is to use the HPLC vial seals with Teflon surfaces. Septa are available with two or even three layers of